CCU2: Which elements from the new "IP" range does it support
Moderator: Co-Administratoren
CCU2: Which elements from the new "IP" range does it support
Hello,
I have a broken movement detector (HM-Sen-MDIR-O-2).
As this type of detector is discontinued I'm searching for a new model compatible with my CCU2.
So more globally, which new elements from the "CCU3/IP" line can the old CCU2 support ?
Tx !
I have a broken movement detector (HM-Sen-MDIR-O-2).
As this type of detector is discontinued I'm searching for a new model compatible with my CCU2.
So more globally, which new elements from the "CCU3/IP" line can the old CCU2 support ?
Tx !
-
- Beiträge: 9750
- Registriert: 27.04.2020, 10:34
- System: CCU
- Hat sich bedankt: 706 Mal
- Danksagung erhalten: 1645 Mal
Re: CCU2: Which elements from the new "IP" range does it support
It is a bit uncertain. Normally you can use all HMIP devices with a CCU2, but since support for the CCU2 has been discontinued, new revisions of devices no longer work with the CCU2. And EQ3 doesn't communicate very openly, so you have to look for little clues like a "-2" or "-A" or something else to identify a revised device. Good luck...
LG, Michael.
Wenn du eine App zur Bedienung brauchst, dann hast du kein Smarthome.
Wettervorhersage über AccuWeather oder OpenWeatherMap+++ Rollladensteuerung 2.0 +++ JSON-API-Ausgaben auswerten +++ undokumentierte Skript-Befehle und Debugging-Tipps +++
Wenn du eine App zur Bedienung brauchst, dann hast du kein Smarthome.
Wettervorhersage über AccuWeather oder OpenWeatherMap+++ Rollladensteuerung 2.0 +++ JSON-API-Ausgaben auswerten +++ undokumentierte Skript-Befehle und Debugging-Tipps +++
- Baxxy
- Beiträge: 10955
- Registriert: 18.12.2018, 15:45
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 621 Mal
- Danksagung erhalten: 2257 Mal
Re: CCU2: Which elements from the new "IP" range does it support
Best bet is to activate/access "DevConfig" on the CCU2.
Under "Device Types" all supported Devices are listed.
Check carefully the exact name like @Michael mentioned.
The original HmIP-Pendant to the HM-Sen-MDIR-O-2 ist the:
HmIP-SMO (white)
HmIP-SMO-A (anthrazit)
Under "Device Types" all supported Devices are listed.
Check carefully the exact name like @Michael mentioned.
The original HmIP-Pendant to the HM-Sen-MDIR-O-2 ist the:
HmIP-SMO (white)
HmIP-SMO-A (anthrazit)
Grüße... Baxxy
- Raspberry Pi 4 als Homematic-Zentrale - Tipps und Informationen
- Analysescript für genutzte Funk-Adressen, Funkmodul-Hardware und Zentralen Hardware
- NANO CUL 868MHz - Stick zum AskSin Analyzer XS umflashen (Anleitung für ArduinoIDE unter Windows)
- Firmware Updates für IP-Aktoren / Sensoren... Info's, Tipps und Sonstiges
- CCU funkt nicht - CarrierSense (CS) Probleme erkennen und lösen
Re: CCU2: Which elements from the new "IP" range does it support
How can I reach that "DevConfig" page ?
Thanks for your replies!
- Baxxy
- Beiträge: 10955
- Registriert: 18.12.2018, 15:45
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 621 Mal
- Danksagung erhalten: 2257 Mal
Re: CCU2: Which elements from the new "IP" range does it support
Just "Google" a little bit.
I don't have a CCU2.
I don't have a CCU2.
Grüße... Baxxy
- Raspberry Pi 4 als Homematic-Zentrale - Tipps und Informationen
- Analysescript für genutzte Funk-Adressen, Funkmodul-Hardware und Zentralen Hardware
- NANO CUL 868MHz - Stick zum AskSin Analyzer XS umflashen (Anleitung für ArduinoIDE unter Windows)
- Firmware Updates für IP-Aktoren / Sensoren... Info's, Tipps und Sonstiges
- CCU funkt nicht - CarrierSense (CS) Probleme erkennen und lösen
-
- Beiträge: 2407
- Registriert: 19.09.2012, 10:53
- System: CCU
- Wohnort: Jottweedee
- Hat sich bedankt: 252 Mal
- Danksagung erhalten: 354 Mal
Re: CCU2: Which elements from the new "IP" range does it support
Go to Settings -> System Control
There you'll find a button "devconfig"
Es kann leider nicht ganz ausgeschlossen werden, dass ich mich irre.
HmIP muss leider draussen bleiben. in Ausnahmefällen erlaubt
ACHTUNG! Per Portweiterleitung aus dem Internet erreichbare CCU-WebUI ist unsicher! AUCH MIT PASSWORTSCHUTZ! Daher: Portweiterleitung deaktivieren!
HmIP muss leider draussen bleiben. in Ausnahmefällen erlaubt
ACHTUNG! Per Portweiterleitung aus dem Internet erreichbare CCU-WebUI ist unsicher! AUCH MIT PASSWORTSCHUTZ! Daher: Portweiterleitung deaktivieren!
-
- Beiträge: 369
- Registriert: 11.02.2020, 12:14
- System: Alternative CCU (auf Basis OCCU)
- Hat sich bedankt: 95 Mal
- Danksagung erhalten: 68 Mal
Re: CCU2: Which elements from the new "IP" range does it support
I don't know for sure if the button is there by default, afaik you have to enable it or access the devconfig menu manually: viewtopic.php?f=31&t=26624
- Roland M.
- Beiträge: 9855
- Registriert: 08.12.2012, 15:53
- System: CCU
- Wohnort: Graz, Österreich
- Hat sich bedankt: 255 Mal
- Danksagung erhalten: 1403 Mal
Re: CCU2: Which elements from the new "IP" range does it support
Hi!
echo CP_DEFCONFIG=1 >>/etc/config/tweaks
Then you can find an new entry DefConfig in Settings > Control Panel (maybe after logout/login).
Roland
The easiest way is to open an ssh session and create a file tweaks with this command:
echo CP_DEFCONFIG=1 >>/etc/config/tweaks
Then you can find an new entry DefConfig in Settings > Control Panel (maybe after logout/login).
Roland
Zur leichteren Hilfestellung bitte unbedingt beachten:
-----------------------------------------------------------------------
1. CCU2 mit ~100 Geräten (in Umstellung auf RaspberryMatic-OVA auf Proxmox-Server)
2. CCU2 per VPN mit ~50 Geräten (geplant: RaspberryMatic auf Charly)
3. CCU2 per VPN mit ~40 Geräten (geplant: RaspberryMatic auf CCU3)
CCU1, Test-CCU2, Raspi 1 mit kleinem Funkmodul, RaspberryMatic als VM unter Proxmox, Access Point,...
- Bezeichnung (HM-... bzw. HmIP-...) der betroffenen Geräte angeben (nicht Artikelnummer)
- Kurzbeschreibung des Soll-Zustandes (Was soll erreicht werden?)
- Kurzbeschreibung des Ist-Zustandes (Was funktioniert nicht?)
- Fehlermeldungen genau abschreiben, besser noch...
- Screenshots von Programmen, Geräteeinstellungen und Fehlermeldungen (direkt als jpg/png) einstellen!
-----------------------------------------------------------------------
1. CCU2 mit ~100 Geräten (in Umstellung auf RaspberryMatic-OVA auf Proxmox-Server)
2. CCU2 per VPN mit ~50 Geräten (geplant: RaspberryMatic auf Charly)
3. CCU2 per VPN mit ~40 Geräten (geplant: RaspberryMatic auf CCU3)
CCU1, Test-CCU2, Raspi 1 mit kleinem Funkmodul, RaspberryMatic als VM unter Proxmox, Access Point,...
Re: CCU2: Which elements from the new "IP" range does it support
So indeed 4 of those seem to be supported by the CCU2:
HmIP-SMO
HmIP-SMO-2
HmIP-SMO-A
HmIP-SMO-A-2
which is strange as ELV just replied that none of those could work with the CCU2 ?!
HmIP-SMO
HmIP-SMO-2
HmIP-SMO-A
HmIP-SMO-A-2
which is strange as ELV just replied that none of those could work with the CCU2 ?!