seit einem reboot steht der State auf "STOPPED" und lässt sich mit allen Tipps aus dem Forum nicht mehr starten.
Raspi 4 4GB mit RPI-RF-MOD
pivccu3
openHab3
Bis auf eine Neuinstallation hab ich (auszugsweise und in unterschiedlicher Reihenfolge) folgendes versucht:
Code: Alles auswählen
sudo apt update && sudo apt upgrade
sudo dpkg-reconfigure pivccu-modules-dkms
sudo dpkg-reconfigure pivccu3
sudo apt remove pivccu-modules-raspberrypi
sudo apt install --reinstall raspberrypi-bootloader raspberrypi-kernel raspberrypi-kernel-headers
sudo apt install pivccu-modules-raspberrypi
sudo apt install --reinstall lxc pivccu3
sudo pivccu-info
Code: Alles auswählen
pi@raspberrypi:~ $ sudo pivccu-info
piVCCU version: 3.55.10-54
Kernel modules: Available
Raw UART dev: Not available
Rasp.Pi UART: Assigned to GPIO pins
HMRF Hardware: unknown
Board serial: unknown
Radio MAC: unknown
HMIP Hardware: unknown
SGTIN: unknown
Radio MAC: unknown
State: STOPPED
Code: Alles auswählen
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2
[all]
#dtoverlay=vc4-fkms-v3d
dtoverlay=pi3-disable-bt
enable_uart=0
dtoverlay=pi3-disable-bt
dtoverlay=pivccu-raspberrypi
Code: Alles auswählen
pivccu.service - piVCCU
Loaded: loaded (/lib/systemd/system/pivccu.service; enabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Thu 2021-02-18 21:42:56 CET; 21min ago
Process: 667 ExecStart=/var/lib/piVCCU3/start_container.sh (code=exited, status=0/SUCCESS)
Main PID: 954 (code=exited, status=1/FAILURE)
Feb 18 21:42:50 raspberrypi piVCCU3[762]: HMIP hardware was not detected
Feb 18 21:42:50 raspberrypi start_container.sh[667]: <12>Feb 18 21:42:50 piVCCU3: HMIP hardware was not detected
Feb 18 21:42:55 raspberrypi start_container.sh[667]: kernel.sched_rt_runtime_us = -1
Feb 18 21:42:56 raspberrypi start_container.sh[667]: lxc-start: lxc: lxccontainer.c: wait_on_daemonized_start: 842 Recei
Feb 18 21:42:56 raspberrypi start_container.sh[667]: lxc-start: lxc: tools/lxc_start.c: main: 330 The container failed to start
Feb 18 21:42:56 raspberrypi start_container.sh[667]: lxc-start: lxc: tools/lxc_start.c: main: 333 To get more details, r
Feb 18 21:42:56 raspberrypi start_container.sh[667]: lxc-start: lxc: tools/lxc_start.c: main: 336 Additional information
Feb 18 21:42:56 raspberrypi systemd[1]: Started piVCCU.
Feb 18 21:42:56 raspberrypi systemd[1]: pivccu.service: Main process exited, code=exited, status=1/FAILURE
Feb 18 21:42:56 raspberrypi systemd[1]: pivccu.service: Failed with result 'exit-code'.